top of page

The Beans Circulate. The Exhaust Doesn't. Why the open-top roasting chamber is central to the Air-Motion design.

Writer: Air-Motion Roasters
Air-Motion Roasters
12 hours ago
5 min read

In our previous article, I asked a rather cheeky question.


Would you recycle your car's exhaust?


It was intended to get people thinking about the air used during coffee roasting.


But now I'd like to take that conversation a little further.


Because when it comes to the Air-Motion Roaster, the interesting part isn't simply that we don't deliberately recirculate roasting exhaust.


It's what we've designed the air to do before it leaves.


Let's start with the roasting chamber:


Most people are familiar with the conventional drum roaster.


Coffee beans tumble inside a rotating drum, receiving heat through a combination of contact with heated surfaces, hot air and thermal radiation.


The typical Fluid-bed roasters take a different approach, using moving hot air to support and heat the beans.


Both technologies can use continuous airflow and exhaust extraction.


However, at Air-Motion Roasters, we've developed our own approach.


Our roasting chamber is vertical, cylindrical and open at the top.


At the bottom, a conical section directs the beans towards a centrally positioned perforated plate.


Heated air enters through this plate and moves upwards through the coffee.


And that's where things become interesting.


One Airstream. Three Important Jobs.


The heated air entering the AMR roasting chamber performs three interconnected functions.


First, it moves the beans.


The upward airflow lifts the coffee through the centre of the chamber.


As the beans rise, they spread outwards and descend along the sides of the roast chamber making contact with the metal chamber walls before returning towards the bottom.


The process repeats, creating the distinctive circulating movement of an Air-Motion roast.


Second, it transfers heat.


As the heated air moves through the coffee, it transfers energy to the beans by convection heat transfer.


As mentioned, during their circulation, the beans also interact with the chamber surfaces, and with one another, creating opportunities for conductive heat transfer.


The movement and heat transfer are interconnected, which is why airflow control is such an important part of operating the machine.


More air = more convection, less air = more conduction.


Third, it carries roasting by-products away.


As the beans heat up, they release moisture, gases, smoke, some volatile organic compounds and particulate matter.


The upward-moving air immediately entrains these substances as they are released from the bean and carries them towards the top of the chamber.


This is a fundamental consideration in our design.


We aren't simply using air to heat the beans.


We're also using it to transport airborne roasting by-products away from the beans towards the extraction.


What’s left in the chamber, just coffee.


Why an open-top chamber?:





A common misconception is that any closed roasting chamber automatically traps smoke and gases.


That isn't necessarily true.


Conventional roasters do have ventilation, and some operate with the extraction system where the operator uses vents to open and close the airflow.


However, the meaningful distinction lies in the design of the airflow path and how efficient they are removing smoke and gases from the roast chamber before they are able to infuse back into the beans.


With AMR's open-top chamber, the heated air moves upwards through the beans and exits towards an extraction hood positioned above the chamber.


There isn't a closed roof forcing the process air to remain within the roasting vessel for any amount of time.


We also don't deliberately return that outgoing roasting air to the beans by recycling the heated air to save on energy costs. (the energy efficiency of the AMR will be discussed later).


So. The beans circulate. The exhaust doesn't.


It's a simple way of describing a deliberate engineering decision.


What happens above the chamber?


Now we come to another part of the system that deserves attention.


There is a deliberately designed gap between the top of the roasting chamber and the extraction hood.


Why?


Because the airflow doesn't simply stop being important when it leaves the beans.


The extraction system draws the outgoing hot process air towards the hood.


At the same time, ambient air enters through the gap and mixes with that outgoing stream.


This mixing reduces the temperature of the combined exhaust and dilutes the concentrations of substances carried in the gas.


The mixed stream then continues through the extraction system.


This is an important distinction.


Cooling and dilution are not the same as destroying pollutants.


Introducing ambient air can lower the temperature and measured concentration of contaminants in the combined stream, but it doesn't automatically remove their total mass.

That's why we also need to understand what happens further along the AMR’s extraction pathway.


The cyclone's job


Part of AMR's extraction arrangement is a cyclone separator.


Its purpose is to separate chaff and other entrained particulate matter from the outgoing airstream.


As the gas moves through the cyclone, its geometry creates a swirling motion that allows particles with sufficient inertia to separate from the gas stream.


It's a mechanical separation process.


And it's different from removing gaseous compounds.


A cyclone can help capture chaff and particles, but it isn't a universal gas purifier.


Understanding that distinction matters when discussing roasting emissions.


So why does all this matter?


Because a coffee roaster isn't just a heater with a container full of beans.


It's a system of interacting processes.


Bean movement influences heat transfer.


Airflow influences bean movement.


Extraction influences the movement of airborne roasting by-products.


And the way the outgoing air is handled affects the exhaust ultimately discharged.


These considerations were part of the engineering thinking behind Air-Motion Roasters.


Over years of developing and operating these machines, I've watched the relationship between airflow, bean circulation and extraction play out during actual roasting.


You can see the beans moving.


You can observe moisture and smoke being carried towards the hood.


But visual observation doesn't establish that every compound has been removed or that none remains in the coffee.


That requires measurement.


And that brings us to the next part of the story.


The part most people never see:


It's easy to look at a coffee roaster and focus on the chamber.


After all, that's where the coffee is.


But I believe the extraction system deserves just as much engineering attention.


Because it's responsible for managing what the process air carries away.


At Air-Motion Roasters, the chamber and extraction system weren't conceived as unrelated pieces of equipment.


They form part of a single airflow process.


We engineered how the air enters. We engineered what it does. And we engineered how it leaves.


So, in the next article, I'll take you behind the roasting chamber to explore our extraction system, the engineering decisions behind it, and what independent emissions testing has actually told us.


In the next episode of - The Air We Roast With:


We Didn't Just Engineer the Heat. We Engineered the Exit.


Air-Motion Roasters — Challenging Convention!


Written by: Julian Platt

Comments


bottom of page